TM 11-6130-392-34
holders with screws (11) and washers (12).
(1) Remove screws (l) and washers (2) holding
(3) Position terminal board TB1 (59) in place
cover (3) to chassis (4) and remove cover.
and fasten with nuts (58).
(2) Remove screws (5) holding printed wiring
(4) Position transformer T1 (18) in place and
board basket assembly (6) in chassis.
fasten with cap screws (17).
(3) Carefully remove basket assembly to gain
(5) Position capacitor C1 (9) In place and fasten
access to screw (7) and washer (8) holding leads to
with washers (8) and screws (7).
negative terminal on capacitor C1 (9); disconnect
(6) Install cover (3) on chassis and fasten with
leads.
screws (1) and washers (2).
(4) Carefully move basket assembly out and
aside.
4-16. Battery Holder (5)
(5) Tag and disconnect leads to battery holders
Removal and installation of battery holder (fig. 4-3)
(10) by removing screws (11) and washers (12).
are as follows:
( 6 ) Remove screws (13) and washers (14),
a. Removal.
holding battery holders (10) to chassis. Remove bat-
(1) Remove screws (1) and washers (2) holding
tery holders.
cover (3) to chassis (4) and remove cover.
b. Installation.
(2) Remove nuts (58) holding terminal board
(1) Position battery holders (10) on chassis (4)
TB1 (59) to chassis. Carefully move TB1 aside.
and fasten with screws (13) and washers (14).
(3) Tag and disconnect leads to battery holder
(2) Remove tags and fasten leads to battery
(10) by removing screws (11) and washers (12).
holders with screws (11) and washers (12).
(4) Remove screws (13) and washers (14) hold-
( 3 ) Position printed w i r i n g b o a r d b a s k e t
i n g battery holder to chassis. Remove battery
assembly (6) in chassis (4).
holder.
(4) Fasten leads to capacitor C1 (9) with screws
b. Installation.
(7) and washers (8).
(1) Position battery holder (10) on chassis (4)
( 5 ) Fasten basket assembly in chassis with
and fasten with screws (13) and washers (14).
screws (5).
(2) Position terminal board TB1 (59) in place
(6) Perform an operational check of battery
and fasten with nuts (58).
charger in accordance with section V.
(3) Install cover (3) on chassis and fasten with
(7) Install retainer on chassis and fasten with
screws (1) and washers (2).
screws.
(8) Install cover (3) on chassis and fasten with
4-17. Filter Capacitor (C1)
screws (1) and washers (2).
Removal and installation of filter capacitor (fig. 4-3)
are as follows:
4-15. Battery Holders (3 and 4)
a. Removal.
Removal and installation of either battery holder
(1) Remove screws (1) and washers (2) holding
(fig. 4-3) are as follows:
cover (3) to chassis (4) and remove cover.
a. Removal.
(2) Peel or pick away red staking compound
(1) Remove screws (1) and washers (2) hold-
over positive (+) terminal of capacitor C1 (9).
ing cover (3) to chassis (4) and remove cover.
(3) Tag leads to capacitor and remove screws
(2) Remove screws (15) and washers (16) hold-
(7) and washers (8).
ing capacitor C1 (9) to chassis. Carefully move
(4) Remove screws (15) and washers (16) hold-
capacitor aside to gain access to bottom of chassis.
ing capacitor to chassis and remove capacitor.
(3) Remove cap screws (17) holding transform-
b. Installation.
er T1 (18) to chassis. Carefully move transformer
(1) Position capacitor C1 (9) on chassis (4) and
out and aside.
fasten with screws (15) and washers (16).
(4) Remove nuts (58) holding terminal board
(2) Remove tags and connect leads to capacitor
TB1 (59) to chassis. Carefully move TB1 aside.
and fasten with screws (7) and washers (8).
(5) Tag and disconnect leads to battery holders
(3) Using red staking compound, apply a 0.04
(10) by removing screws (11) and washers (12).
to 0.08 inch coating over positive (+) terminal of
(6) Remove screws (13) and washers (14) hold-
capacitor.
i n g battery holders to chassis. Remove battery
(4) Install cover (3) on chassis and fasten with
holders.
screws (1) and washers (2).
b. Installation.
4-18. Transformer (T1)
(1) Position battery holders (10) on chassis (4)
and fasten with screws (13) and washers (14).
Removal and installation of transformer (fig. 4-3)
are as follows:
(2) Remove tags and fasten leads to battery
4-18
