TB 11-6135-200-25
0.50 ohms. (Alinco Model 101-5A Igniter Circuit Tester
connector and shall be 0.45 to 0.65 ohms.
The
or approved equal).
maximum current during this test shall be limited to 10
c. Insulation Resistance. The insulation resistnace shall
milliamperes. This test should be preformed as quickly
be measured with a 500 20 vdc megohmeter, (Weston
as possible.
Model #796 or approved equal). The 500 20 vdc shall
e. Insulation Resistance. The insulation resistance of
be applied to the battery terminals and for the specified
the battery shall be greater than 10 megohms, when
time stated in the chart below. The battery insulation
applying 500 50 vdc and limiting the current to 5
resistance shall not be less than 1 megohm. Current
milliamperes, between each of the battery connector
shall be limited to 5 milliamperes during test.
contacts and battery case. Potential shall be applied to
500 vdc potential
each test circuit for a maximum of 2 minutes.
Positive
Negative
Minimum Time Period
+ terminal
-M & M terminal
5 seconds
6-8. Serviceability Test for Battery, Dry Thermal BA-
+ terminal
Battery case
5 seconds
630/U.
- M & M terminal Batter), case
5 seconds
a. Visual Inspection. Examine all battery headers and
M terminal
Battery case
5 seconds
cases for cracks, dents, scratches, breaks, burrs, loose
parts, etc. Examine all connector pin contacts for signs
6-7. Serviceability Test for Battery, Dry Thermal BA-
of corrosion, missing or flaking plating, bent pins, etc.
629/U.
Examine all grommets for cracks, holes, tears, or
a. Visual Inspection. Examine all battery headers and
b. Battery Voltage. The voltage of the battery at room
cases for cracks, dents, scratches, breaks, burrs, loose
temperature, shall not exceed 0.05 volts dc when
parts, etc. Examine all connector pin contacts for signs
of corrosion, missing or flaking plating, bent pins, etc.
megohms or greater when connected between pin F
Examine all grommets for cracks, holes, tears, or
(positive) and pin B (negative) of the battery connector.
b. Circuit Resistance. Using the four-wire method (volt-
c. Squib Circuit Resistance. The squib resistance shall
ampere method) measure and record the ohms values
be measured across pins J and K of the battery
between battery connector A and B, H and A, H and B, F
connector and shall be 0.45 to 0.65 ohms.
The
and E, E and D, and F and D, record all measurements.
maximum current during this test shall be limited to 10
c. Battery Voltage. The voltage of the battery at room
milliamperes. This test should be performed as quickly
as possible.
Temperature, shall not exceed 0.05 volts dc when
d. Insulation resistance. The insulation resistance of the
battery shall be greater than 10 megohms, when
megohms or greater, when connected between pin D
applying 500 50 vdc and limiting the current to 5
(positive) and pin A (negative); between pin E (positive)
milliamperes, between each of the battery connector
and pin B (negative); and between pin F (positive) and
contacts and the battery case.
pin H (negative) of the battery connector.
d. Squib Circuit Resistance. The squib resistance shall
be measured across pins J and K of the battery
SECTION VII
PRESERVATION AND PACKAGING BATTERY, DRY, THERMAL
(e) Unit packaging. Batteries in the quantities specified
7-1. Battery, Dry, Thermal B-415, BA-605/U, BA-
in the chart given in paragraph 2, and of the same type
617/JU, BA-6271U, BA-628/U, BA-629/U and BA-630/U
and date of manufacture shall be packaged in
a. Preservation and Packaging. Preservation and
accordance with method IC-2 of MIL-P-116. Batteries
packaging shall be level A, B, or C, as specified.
shall be placed in a close-fitting box conforming to
(1) Level A.
PPPB-566, variety 1, or a close-fitting box conforming to
(a) Cleaning. Cleaning shall be accomplished in
PPP-B-636, type CF, class domestic, style optional.
accordance with process C-I of MIL-P-116.
Closure shall be as specified in the appendix to the
(b) Drying. Drying shall be accomplished in accordance
applicable box specification. The boxed batteries shall
with the applicable procedures of MIL-P-116.
be placed in a barrier bag fabricated of material
(c) Preservation application. None required.
conforming to L-P-378, type I, grade B, finish I, having a
(d) Prepackaging. Batteries unit packaged in qualities
uniform thickness of 4.0 +0.5 mils. Closure of the bag
greater than one each shall be individually placed in
shall be by heat seal. The bagged batteries shall be
polyethylene bag fabricated or material conforming to L-
placed in a close-fitting paperboard box conforming to
P-378, type 1, grade B, finish 1, having minimum
Mll.B-43014, or a close-fitting fiberboard box conforming
:hickness of 2.0 mils. Closure of the bag shall be by heat
to PPP-B-636, grade W6c or W5c, style optional. Close
seal.
the box in accordance with the appendix to the
applicable box specification.
27